All port groups on standard switches must not be configured to virtual local area network (VLAN) 4095 unless Virtual Guest Tagging (VGT) is required.

Overview

Finding ID	Version	Rule ID	IA Controls	Severity
V-256425	ESXI-70-000064	SV-256425r886056_rule		Medium

Description
When a port group is set to VLAN 4095, the vSwitch passes all network frames to the attached virtual machines (VMs) without modifying the VLAN tags. In vSphere, this is referred to as VGT. The VM must process the VLAN information itself via an 802.1Q driver in the operating system. VLAN 4095 must only be implemented if the attached VMs have been specifically authorized and are capable of managing VLAN tags themselves. If VLAN 4095 is enabled inappropriately, it may cause denial of service or allow a VM to interact with traffic on an unauthorized VLAN.

Description

When a port group is set to VLAN 4095, the vSwitch passes all network frames to the attached virtual machines (VMs) without modifying the VLAN tags. In vSphere, this is referred to as VGT. The VM must process the VLAN information itself via an 802.1Q driver in the operating system. VLAN 4095 must only be implemented if the attached VMs have been specifically authorized and are capable of managing VLAN tags themselves. If VLAN 4095 is enabled inappropriately, it may cause denial of service or allow a VM to interact with traffic on an unauthorized VLAN.

STIG	Date
VMware vSphere 7.0 ESXi Security Technical Implementation Guide	2023-02-21

Details

Check Text ( C-60100r886054_chk )
Note: This control addresses ESXi standard switches. Distributed switches are addressed in the vCenter STIG. If there is no standard switch on the ESXi host, this is not applicable. From the vSphere Client, go to Hosts and Clusters. Select the ESXi Host >> Configure >> Networking >> Virtual switches. For each standard switch, review the "VLAN ID" on each port group and verify it is not set to "4095". or From a PowerCLI command prompt while connected to the ESXi host, run the following command: Get-VirtualPortGroup -Standard \| Select Name, VLanId If any port group is configured with VLAN 4095 and is not documented as a needed exception, this is a finding.

Check Text ( C-60100r886054_chk )

Note: This control addresses ESXi standard switches. Distributed switches are addressed in the vCenter STIG. If there is no standard switch on the ESXi host, this is not applicable.

From the vSphere Client, go to Hosts and Clusters.

Select the ESXi Host >> Configure >> Networking >> Virtual switches.

For each standard switch, review the "VLAN ID" on each port group and verify it is not set to "4095".

or

From a PowerCLI command prompt while connected to the ESXi host, run the following command:

Get-VirtualPortGroup -Standard | Select Name, VLanId

If any port group is configured with VLAN 4095 and is not documented as a needed exception, this is a finding.

Fix Text (F-60043r886055_fix)
From the vSphere Client, go to Hosts and Clusters. Select the ESXi Host >> Configure >> Networking >> Virtual switches. For each port group on a standard switch that is configured to a native VLAN, click the "..." button next to the port group. Click "Edit Settings". On the "Properties" tab, change the "VLAN ID" to an appropriate VLAN ID and click "OK". or From a PowerCLI command prompt while connected to the ESXi host, run the following command: Get-VirtualPortGroup -Name "portgroup name" \| Set-VirtualPortGroup -VLanId "New VLAN#"

Fix Text (F-60043r886055_fix)

From the vSphere Client, go to Hosts and Clusters.

Select the ESXi Host >> Configure >> Networking >> Virtual switches.

For each port group on a standard switch that is configured to a native VLAN, click the "..." button next to the port group.

Click "Edit Settings". On the "Properties" tab, change the "VLAN ID" to an appropriate VLAN ID and click "OK".

or

From a PowerCLI command prompt while connected to the ESXi host, run the following command:

Get-VirtualPortGroup -Name "portgroup name" | Set-VirtualPortGroup -VLanId "New VLAN#"