The vCenter Server must not configure VLAN Trunking unless Virtual Guest Tagging (VGT) is required and authorized.

Overview

Finding ID	Version	Rule ID	IA Controls	Severity
V-243087	VCTR-67-000019	SV-243087r816914_rule		Medium

Description
When a port group is set to VLAN Trunking, the vSwitch passes all network frames in the specified range to the attached VMs without modifying the VLAN tags. In vSphere, this is referred to as Virtual Guest Tagging (VGT). The VM must process the VLAN information itself via an 802.1Q driver in the OS. VLAN Trunking must only be implemented if the attached VMs have been specifically authorized and are capable of managing VLAN tags themselves. If VLAN Trunking is enabled inappropriately, it may cause denial of service or allow a VM to interact with traffic on an unauthorized VLAN.

Description

When a port group is set to VLAN Trunking, the vSwitch passes all network frames in the specified range to the attached VMs without modifying the VLAN tags. In vSphere, this is referred to as Virtual Guest Tagging (VGT). The VM must process the VLAN information itself via an 802.1Q driver in the OS. VLAN Trunking must only be implemented if the attached VMs have been specifically authorized and are capable of managing VLAN tags themselves. If VLAN Trunking is enabled inappropriately, it may cause denial of service or allow a VM to interact with traffic on an unauthorized VLAN.

STIG	Date
VMware vSphere 6.7 vCenter Security Technical Implementation Guide	2022-01-04

Details

Check Text ( C-46362r816850_chk )
If distributed switches are not used, this is not applicable. From the vSphere Client, go to Networking >> select a distributed switch >> select a distributed port group >> Configure >> Settings >> Policies. Review the port group "VLAN Type" and "VLAN trunk range", if present. or From a PowerCLI command prompt while connected to the vCenter server, run the following command: Get-VDPortgroup \| Where {$_.ExtensionData.Config.Uplink -ne "True"} \| select Name,VlanConfiguration If any port group is configured with "VLAN Trunk" and is not documented as a needed exception (such as NSX appliances), this is a finding. If any port group is authorized to be configured with "VLAN trunking" but is not configured with the most limited range necessary, this is a finding.

Check Text ( C-46362r816850_chk )

If distributed switches are not used, this is not applicable.

From the vSphere Client, go to Networking >> select a distributed switch >> select a distributed port group >> Configure >> Settings >> Policies.

Review the port group "VLAN Type" and "VLAN trunk range", if present.

or

From a PowerCLI command prompt while connected to the vCenter server, run the following command:

Get-VDPortgroup | Where {$_.ExtensionData.Config.Uplink -ne "True"} | select Name,VlanConfiguration

If any port group is configured with "VLAN Trunk" and is not documented as a needed exception (such as NSX appliances), this is a finding.

If any port group is authorized to be configured with "VLAN trunking" but is not configured with the most limited range necessary, this is a finding.

Fix Text (F-46319r719503_fix)
From the vSphere Client, go to Networking >> select a distributed switch >> select a distributed port group >> Configure >> Settings >> Policies. Click "Edit". Click the "VLAN" tab. If "VLAN trunking" is not authorized, remove it by setting "VLAN type" to "VLAN" and configure an appropriate VLAN ID. Click "OK". If "VLAN trunking" is authorized but the range is too broad, modify the range in the "VLAN trunk range" field to the minimum necessary and authorized range. An example range would be "1,3-5,8". Click "OK". or From a PowerCLI command prompt while connected to the vCenter server, run the following command to configure trunking: Get-VDPortgroup "Portgroup Name" \| Set-VDVlanConfiguration -VlanTrunkRange "" or Run this command to configure a single VLAN ID: Get-VDPortgroup "Portgroup Name" \| Set-VDVlanConfiguration -VlanId ""

Fix Text (F-46319r719503_fix)

From the vSphere Client, go to Networking >> select a distributed switch >> select a distributed port group >> Configure >> Settings >> Policies.

Click "Edit".

Click the "VLAN" tab.

If "VLAN trunking" is not authorized, remove it by setting "VLAN type" to "VLAN" and configure an appropriate VLAN ID. Click "OK".

If "VLAN trunking" is authorized but the range is too broad, modify the range in the "VLAN trunk range" field to the minimum necessary and authorized range. An example range would be "1,3-5,8". Click "OK".

or

From a PowerCLI command prompt while connected to the vCenter server, run the following command to configure trunking:

Get-VDPortgroup "Portgroup Name" | Set-VDVlanConfiguration -VlanTrunkRange ""

or

Run this command to configure a single VLAN ID:

Get-VDPortgroup "Portgroup Name" | Set-VDVlanConfiguration -VlanId ""