Traffic entering the tunnels is not restricted to only the authorized management packets based on destination address.

Overview

Finding ID	Version	Rule ID	IA Controls	Severity
V-17835	NET1006	SV-19311r1_rule		Medium

Description
Similar to the OOBM model, when the production network is managed in-band, the management network could also be housed at a NOC that is located locally or remotely at a single or multiple interconnected sites. NOC interconnectivity as well as connectivity between the NOC and the managed networks’ premise routers would be enabled using either provisioned circuits or VPN technologies such as IPSec tunnels or MPLS VPN services.

Description

Similar to the OOBM model, when the production network is managed in-band, the management network could also be housed at a NOC that is located locally or remotely at a single or multiple interconnected sites. NOC interconnectivity as well as connectivity between the NOC and the managed networks’ premise routers would be enabled using either provisioned circuits or VPN technologies such as IPSec tunnels or MPLS VPN services.

STIG	Date
Perimeter Router Security Technical Implementation Guide Juniper	2016-12-23

Details

Check Text ( C-20260r1_chk )
Verify that all traffic from the managed network to the management network and vice-versa is secured via IPSec encapsulation. In the configuration examples, 10.2.2.0/24 is the management network at the NOC and 192.168.1.0/24 is address space used at the network being managed (i.e., the enclave). Example from a show services command with Juniper M or T series router with Adaptive Services PIC using next-hop style is as follows: service-set vpn-to-NOC { next-hop-service { inside-service-interface sp-0/0/0.1; outside-service-interface sp-0/0/0.2; } ipsec-vpn-options { local-gateway 19.16.1.1; } ipsec-vpn-rules site-to-NOC; } ipsec-vpn { rule site-to-NOC { term mgmt-traffic { } destination-address { 10.2.2.0/24; } } then remote-gateway 19.16.2.1; dynamic { ike-policy main_mode_ike_policy; ipsec-policy dynamic_ipsec_policy; } } } match-direction input; } ipsec { proposal esp_sha1_ipsec_prop { protocol esp; authentication-algorithm hmac-sha1-96; encryption-algorithm 3des-cbc; } policy dynamic_ipsec_policy { perfect-forward-secrecy { keys group2; } proposals esp_sha1_ipsec_prop; } } ike { proposal psk_sha1_3des_ike_prop { authentication-method pre-shared-keys; authentication-algorithm sha1; encryption-algorithm 3des-cbc; } policy main_mode_ike_policy { mode main; proposals psk_sha1_3des_ike_prop; pre-shared-key ascii-text “$7#$AAtBRmNOjH”; ##SECRET-DATA } } } Note: Juniper recommends implementing all Layer 3 services with the next-hop-style service set as opposed to the interface-style. When you configure next-hop-style service sets, you associate them with specific inside and outside logical interfaces. These logical interfaces are units you configure on an AS PIC’s sp- interface as illustrated below: interfaces { sp-0/0/0 { unit 0 { family inet; } unit 1 { description "IPSec Tunnel Inside Service Interface"; family inet; service-domain inside; } unit 2 { description "IPSec Tunnel Outside Service Interface"; family inet; service-domain outside; } } … … } The router must be configured to match the traffic that is to be secured in the outbound direction. For next-hop service sets, this is the input direction as configured via match-direction input command as shown above under the services ipsec-vpn hierarchy. You configure the router to route traffic to the inside or outside interface as shown in the following example: routing-options { static { route 10.2.2.0/24 next-hop sp-0/0/0.1; } }

Check Text ( C-20260r1_chk )

Verify that all traffic from the managed network to the management network and vice-versa is secured via IPSec encapsulation. In the configuration examples, 10.2.2.0/24 is the management network at the NOC and 192.168.1.0/24 is address space used at the network being managed (i.e., the enclave). Example from a show services command with Juniper M or T series router with Adaptive Services PIC using next-hop style is as follows:

service-set vpn-to-NOC {
next-hop-service {
inside-service-interface sp-0/0/0.1;
outside-service-interface sp-0/0/0.2;
}
ipsec-vpn-options {
local-gateway 19.16.1.1;
}
ipsec-vpn-rules site-to-NOC;
}
ipsec-vpn {
rule site-to-NOC {
term mgmt-traffic {
}
destination-address {
10.2.2.0/24;
}
}
then
remote-gateway 19.16.2.1;
dynamic {
ike-policy main_mode_ike_policy;
ipsec-policy dynamic_ipsec_policy;
}
}
}
match-direction input;
}
ipsec {
proposal esp_sha1_ipsec_prop {
protocol esp;
authentication-algorithm hmac-sha1-96;
encryption-algorithm 3des-cbc;
}
policy dynamic_ipsec_policy {
perfect-forward-secrecy {
keys group2;
}
proposals esp_sha1_ipsec_prop;
}
}
ike {
proposal psk_sha1_3des_ike_prop {
authentication-method pre-shared-keys;
authentication-algorithm sha1;
encryption-algorithm 3des-cbc;
}
policy main_mode_ike_policy {
mode main;
proposals psk_sha1_3des_ike_prop;
pre-shared-key ascii-text “$7#$AAtBRmNOjH”; ##SECRET-DATA
}
}
}

Note: Juniper recommends implementing all Layer 3 services with the next-hop-style service set as opposed to the interface-style. When you configure next-hop-style service sets, you associate them with specific inside and outside logical interfaces. These logical interfaces are units you configure on an AS PIC’s sp- interface as illustrated below:

interfaces {
sp-0/0/0 {
unit 0 {
family inet;
}
unit 1 {
description "IPSec Tunnel Inside Service Interface";
family inet;
service-domain inside;
}
unit 2 {
description "IPSec Tunnel Outside Service Interface";
family inet;
service-domain outside;
}
}
…
…
}

The router must be configured to match the traffic that is to be secured in the outbound direction. For next-hop service sets, this is the input direction as configured via match-direction input command as shown above under the services ipsec-vpn hierarchy. You configure the router to route traffic to the inside or outside interface as shown in the following example:

routing-options {
static {
route 10.2.2.0/24 next-hop sp-0/0/0.1;
}
}

Fix Text (F-17752r1_fix)
Where IPSec technology is deployed to connect the managed network to the NOC, it is imperative that the traffic entering the tunnels is restricted to only the authorized management packets based on destination address.