| V-3062 | High | The network element must be configured to ensure passwords are not viewable when displaying configuration information. | Many attacks information systems and network elements are launched from within the network. Hence, it is imperative that all passwords are encrypted so they cannot be intercepted by viewing the... |
| V-15434 | High | The emergency account must be set to an appropriate authorization level to perform necessary administrative functions when the authentication server is not online. | The emergency account is to be configured as a local account on the network devices. It is to be used only when the authentication server is offline or not reachable via the network. The emergency... |
| V-14689 | High | Inbound IP packets with a local host loopback address (127.0.0.0/8) must be blocked, denied, or dropped at the perimeter device. | This type of IP address spoofing occurs when someone outside the network uses a local host address to gain access to systems or devices on the internal network. If the intruder is successful, they... |
| V-3012 | High | Network devices must be password protected. | Network access control mechanisms interoperate to prevent unauthorized access and to enforce the organization's security policy. Access to the network must be categorized as administrator, user,... |
| V-14696 | High | The network element must be configured to restrict the acceptance of any IP packets from the unspecified address, (0:0:0:0:0:0:0:0 or ::/128). | The address 0:0:0:0:0:0:0:0, also defined ::/128 is called the unspecified address. It must never be assigned to any node. It indicates the absence of an address. One example of its use is in... |
| V-14694 | High | The network element will be configured to ensure IPv6 Site Local Unicast addresses are blocked on the ingress inbound filter, (FEC0::/10). Note that this consist of all addresses that begin with FEC, FED, FEE and FEF. | As currently defined, site local addresses are ambiguous and can be present in multiple sites. The address itself does not contain any indication of the site to which it belongs. The use of... |
| V-14695 | High | The network element must be configured restrict to accept the device from accepting any inbound IP packets with a local host loop back address, (0:0:0:0:0:0:0:1 or ::1/128). | The unicast address 0:0:0:0:0:0:0:1, also defined ::1/128 is called the loopback address. A node could use it to send an IPv6 packet to itself. It should never be assigned to any physical... |
| V-14692 | High | Inbound IP packets using RFC 1918 address space (10.0.0.0/8, 172.16.0.0 /12, and 192.168.0 /16) must be blocked, denied, or dropped at the perimeter device. | This type of IP address spoofing occurs when someone outside the network uses an RFC1918 address to gain access to systems or devices on the internal network. If the intruder is successful, they... |
| V-14690 | High | Inbound IP packets using link-local address space (169.254.0.0/16) must be blocked, denied, or dropped at the perimeter device. | This type of IP address spoofing occurs when someone outside the network uses a link-local address to gain access to systems or devices on the internal network. If the intruder is successful, they... |
| V-14691 | High | Inbound packets using IP addresses specified in the RFC5735 and RFC6598, along with network address space allocated by IANA, but not assigned by the RIRs for ISP and other end-customer use must be blocked, denied, or dropped at the perimeter device. | This type of IP address spoofing occurs when someone outside the network uses an address that should not be routed or has not been officially assigned to an ISP for use by the RIR to gain access... |
| V-4582 | High | The network device must require authentication for console access. | Network devices with no password for administrative access via the console provide the opportunity for anyone with physical access to the device to make configuration changes enabling them to... |
| V-18640 | High | Tunneled packets must be filtered at the tunnel exit point. | Once a tunnel has been terminated, the inner packet is no different than any other packet. Therefore, the inner packet must be filtered at the tunnel exit point network. In fact, some packets... |
| V-4622 | High | The IAO/NSO will ensure premise router interfaces that connect to an AG (i.e., ISP) are configured with an ingress ACL that only permits packets with destination addresses within the site’s address space. | Any enclave with one or more AG connections will have to take additional steps to ensure that neither their network nor the NIPRNet is compromised. Without verifying the destination address of... |
| V-3175 | High | The network devices must require authentication prior to establishing a management connection for administrative access. | Network devices with no password for administrative access via a management connection provide the opportunity for anyone with network access to the device to make configuration changes enabling... |
| V-3164 | High | The network device must not accept any outbound IP packets that contain an illegitimate address in the source address field by enabling Unicast Reverse Path Forwarding (uRPF) Strict mode or via egress ACL. | When Unicast Reverse Path Forwarding (uRPF) provides an IP address spoof protection capability. When uRPF is enabled in strict mode, the packet must be received on the interface that the router... |
| V-3210 | High | The network device must not use the default or well-known SNMP community strings public and private. | Network devices may be distributed by the vendor pre-configured with an SNMP agent using the well-known SNMP community strings public for read only and private for read and write authorization. An... |
| V-3196 | High | The network device must use SNMP Version 3 Security Model with FIPS 140-2 validated cryptography for any SNMP agent configured on the device. | SNMP Versions 1 and 2 are not considered secure. Without the strong authentication and privacy that is provided by the SNMP Version 3 User-based Security Model (USM), an unauthorized user can gain... |
| V-25037 | High | The IAO will ensure that the router or firewall software has been upgraded to mitigate the risk of DNS cache poisoning attack caused by a flawed PAT implementation using a predictable source port allocation method for DNS query traffic. | DNS cache poisoning is an attack technique that allows an attacker to introduce forged DNS information into the cache of a caching name server. There are inherent deficiencies in the DNS protocol... |
| V-4623 | High | The IAO/NSO will ensure the premise router does not have a routing protocol session with a peer router belonging to an AS (Autonomous System) of the AG service provider. A static route is the only acceptable route to an AG. | The premise router will not use a routing protocol to advertise NIPRNet addresses to the AG. Most ISPs use Border Gateway Protocol (BGP) to share route information with other autonomous systems... |
| V-3056 | High | Group accounts must not be configured for use on the network device. | Group accounts configured for use on a network device do not allow for accountability or repudiation of individuals using the shared account. If group accounts are not changed when someone leaves... |
| V-7009 | High | The lifetime of the MD5 Key expiration must be set to never expire. The lifetime of the MD5 key will be configured as infinite for route authentication, if supported by the current approved router software version. | Only Enhanced Interior Gateway Routing Protocol (EIGRP) and Routing Information Protocol (RIP) Version 2 use key chains. When configuring authentication for routing protocols that provide key... |
| V-15294 | High | Teredo packets must be blocked inbound to the enclave and outbound from the enclave. | Teredo (RFC 4380) is a tunneling mechanism that allows computers to encapsulate IPv6 packets inside IPv4 to traverse IPv4-only networks. It relies on UDP to allow the tunnel to traverse NAT... |
| V-3143 | High | Network devices must not have any default manufacturer passwords. | Network devices not protected with strong password schemes provide the opportunity for anyone to crack the password thus gaining access to the device and causing network outage or denial of... |
| V-3069 | Medium | Management connections to a network device must be established using secure protocols with FIPS 140-2 validated cryptographic modules. | Administration and management connections performed across a network are inherently dangerous because anyone with a packet sniffer and access to the right LAN segment can acquire the network... |
| V-31285 | Medium | The network element must authenticate all BGP peers within the same or between autonomous systems (AS). | As specified in RFC 793, TCP utilizes sequence checking to ensure proper ordering of received packets. RFC 793 also specifies that RST (reset) control flags should be processed immediately,... |
| V-15432 | Medium | Network devices must use two or more authentication servers for the purpose of granting administrative access. | The use of Authentication, Authorization, and Accounting (AAA) affords the best methods for controlling user access, authorization levels, and activity logging. By enabling AAA on the routers in... |
| V-3013 | Medium | Network devices must display the DoD-approved logon banner warning. | All network devices must present a DoD-approved warning banner prior to a system administrator logging on. The banner should warn any unauthorized user not to proceed. It also should provide clear... |
| V-5646 | Medium | The network device must drop half-open TCP connections through filtering thresholds or timeout periods. | A TCP connection consists of a three-way handshake message sequence. A connection request is transmitted by the originator, an acknowledgement is returned from the receiver, and then an acceptance... |
| V-14685 | Medium | The network element must be configured to ensure the routing header extension type 0, 1, and 3-255 are rejected in an IPv6 enclave. | The Routing header is used by an IPv6 source to specify a list of intermediate nodes that a packet has to traverse on the path to its destination. If the packet cannot take the path, it is... |
| V-14687 | Medium | The network element can permit outbound ICMPv6 messages Packet-too-big (type 2), Echo Request (type 128), and Neighborhood Discovery (type 135-136). Remaining ICMPv6 messages must be blocked outbound. | Scanning will usually be the major stage of an information gathering process a malicious computer attacker will lunch against a targeted network. With this stage the malicious computer attacker... |
| V-14686 | Medium | The network element can permit inbound ICMPv6 messages Packet-too-big (type 2), Time Exceeded (type 3), Parameter Problem (type 4), Echo Reply (type 129), and Neighbor Discovery (type 135-136). Remaining ICMPv6 messages must be blocked inbound. | Scanning will usually be the major stage of an information gathering process a malicious computer attacker will launch against a targeted network. With this stage the malicious computer attacker... |
| V-14669 | Medium | The administrator must ensure BSD r command services are disabled. | Berkeley Software Distribution (BSD) “r” commands allow users to execute commands on remote systems using a variety of protocols. The BSD "r" commands (e.g., rsh, rlogin, rcp, rdump, rrestore,... |
| V-28784 | Medium | A service or feature that calls home to the vendor must be disabled. | Call home services or features will routinely send data such as configuration and diagnostic information to the vendor for routine or emergency analysis and troubleshooting. The risk that... |
| V-30618 | Medium | The administrator must ensure the perimeter router is configured to drop all inbound and outbound IPv6 packets containing a Destination Option header with invalid option type values. | These options are intended to be for the Hop-by-Hop header only. The optional and extensible natures of the IPv6 extension headers require higher scrutiny since many imiplementtions do not always... |
| V-14697 | Medium | The network device must block IPv6 multicast addresses used as a source address. | IPv6 multicast addresses should never be a source address. They should only be destination addresses. |
| V-14693 | Medium | The network device must be configured to ensure IPv6 Site Local Unicast addresses are not defined in the enclave, (FEC0::/10). Note that this consist of all addresses that begin with FEC, FED, FEE and FEF. | As currently defined, site local addresses are ambiguous and can be present in multiple sites. The address itself does not contain any indication of the site to which it belongs. The use of... |
| V-14698 | Medium | The IAO/NSO will ensure IPv6 addresses with embedded IPv4-compatible IPv6 addresses are blocked on the ingress and egress filters, (0::/96). | The IPv6 transition mechanisms include a technique for hosts and routers to dynamically tunnel IPv6 packets over IPv4 routing infrastructure. IPv6 nodes that use this technique are assigned... |
| V-14699 | Medium | The IAO/NSO will ensure that IPv6 addresses with embedded IPv4-mapped IPv6 addresses are blocked on the ingress and egress filters, (0::FFFF/96). | The IPv6 transition mechanisms include a technique for hosts and routers to dynamically tunnel IPv6 packets over IPv4 routing infrastructure. IPv6 nodes that use this technique are assigned... |
| V-5645 | Medium | Cisco Express Forwarding (CEF) must be enabled on all supported Cisco Layer 3 IP devices. | The Cisco Express Forwarding (CEF) switching mode replaces the traditional Cisco routing cache with a data structure that mirrors the entire system routing table. Because there is no need to build... |
| V-18647 | Medium | Tunnel end-points must implement filters in accordance with mitigations defined in PPS Vulnerability Assessments. | Allowing unknown traffic into the enclave creates high risk and potential compromise by an intruder. Protocols used by applications the PPSM has reviewed and determined to require additional... |
| V-17814 | Medium | Gateway configuration at the remote VPN end-point is a not a mirror of the local gateway | The IPSec tunnel end points may be configured on the OOBM gateway routers connecting the managed network and the NOC. They may also be configured on a firewall or VPN concentrator located behind... |
| V-14670 | Medium | The network element must be configured so that ICMPv6 unreachable notifications and redirects are disabled on all external facing interfaces. | The Internet Control Message Protocol version 6 (ICMPv6) supports IPv6 traffic by relaying information about paths, routes, and network conditions. Routers automatically send ICMPv6 messages under... |
| V-14671 | Medium | The network element must authenticate all NTP messages received from NTP servers and peers. | Since NTP is used to ensure accurate log file timestamp information, NTP could pose a security risk if a malicious user were able to falsify NTP information. To launch an attack on the NTP... |
| V-3043 | Medium | The network device must use different SNMP community names or groups for various levels of read and write access. | Numerous vulnerabilities exist with SNMP; therefore, without unique SNMP community names, the risk of compromise is dramatically increased. This is especially true with vendors default community... |
| V-17835 | Medium | Traffic entering the tunnels is not restricted to only the authorized management packets based on destination address. | Similar to the OOBM model, when the production network is managed in-band, the management network could also be housed at a NOC that is located locally or remotely at a single or multiple... |
| V-17834 | Medium | An inbound ACL is not configured for the management network sub-interface of the trunk link to block non-management traffic.
| If the management systems reside within the same layer 2 switching domain as the managed network elements, then separate VLANs will be deployed to provide separation at that level. In this case,... |
| V-30744 | Medium | The administrator must ensure the that all L2TPv3 sessions are authenticated prior to transporting traffic. | L2TPv3 sessions can be used to transport layer-2 protocols across an IP backbone. These protocols were intended for link-local scope only and are therefore less defended and not as well-known. As... |
| V-3160 | Medium | The network element must be running a current and supported operating system with all IAVMs addressed. | Network devices that are not running the latest tested and approved versions of software are vulnerable to network attacks. Running the most current, approved version of system and device software... |
| V-3165 | Medium | The IAO/NSO will implement tcp intercept features provided by the router or implement a filter to rate limit tcp syn to protect servers from any TCP SYN flood attacks from an outside network. | The TCP SYN attack involves transmitting a volume of connections that cannot be completed at the destination. This attack causes the connection queues to fill up, thereby denying service to... |
| V-5613 | Medium | The network element must be configured for a maximum number of unsuccessful SSH login attempts set at 3 before resetting the interface. | An attacker may attempt to connect to the device using SSH by guessing the authentication method and authentication key or shared secret. Setting the authentication retry to 3 or less strengthens... |
| V-5612 | Medium | The network element must be configured to timeout after 60 seconds or less for incomplete or broken SSH sessions. | An attacker may attempt to connect to the device using SSH by guessing the authentication method, encryption algorithm, and keys. Limiting the amount of time allowed for authenticating and... |
| V-3969 | Medium | The network device must only allow SNMP read-only access. | Enabling write access to the device via SNMP provides a mechanism that can be exploited by an attacker to set configuration variables that can disrupt network operations. |
| V-3968 | Medium | The administrator must bind the ingress ACL filtering packets entering the network to the external interface on an inbound direction. | Access lists are used to separate data traffic into that which it will route (permitted packets) and that which it will not route (denied packets). Secure configuration of routers makes use of... |
| V-5611 | Medium | The network element must only allow management connections for administrative access from hosts residing in to the management network. | Remote administration is inherently dangerous because anyone with a sniffer and access to the right LAN segment, could acquire the device account and password information. With this intercepted... |
| V-3967 | Medium | The network element must time out access to the console port after 10 minutes or less of inactivity. | Terminating an idle session within a short time period reduces the window of opportunity for unauthorized personnel to take control of a management session enabled on the console or console port... |
| V-3966 | Medium | The emergency account must be limited to a single local account on the device. | Authentication for administrative access to the device is required at all times. A single account can be created on the device's local database for use in an emergency such as when the... |
| V-19188 | Medium | The router must have control plane protection enabled. | The Route Processor (RP) is critical to all network operations as it is the component used to build all forwarding paths for the data plane via control plane processes. It is also instrumental... |
| V-17821 | Medium | The network element’s OOBM interface must be configured with an OOBM network address. | The OOBM access switch will connect to the management interface of the managed network elements. The management interface of the managed network element will be directly connected to the OOBM... |
| V-17822 | Medium | The network elements management interface must be configured with both an ingress and egress ACL. | The OOBM access switch will connect to the management interface of the managed network elements. The management interface can be a true OOBM interface or a standard interface functioning as the... |
| V-17829 | Medium | The gateway router for the managed network is not configured with an ACL or filter on the egress interface to block all outbound management traffic. | The management network must still have its own subnet in order to enforce control and access boundaries provided by Layer 3 network nodes such as routers and firewalls. Management traffic between... |
| V-15288 | Medium | ISATAP tunnels must terminate at an interior router. | ISATAP is an automatic tunnel mechanism that does not provide authentication such as IPSec. As a result of this limitation, ISATAP is thought of as a tool that is used inside the enclave among... |
| V-5731 | Medium | The SA will utilize ingress and egress ACLs to restrict traffic destined to the enclave perimeter in accordance with the guidelines contained in DoD Instruction 8551.1 for all ports and protocols required for operational commitments. | Vulnerability assessments must be reviewed by the SA and protocols must be approved by the IA staff before entering the enclave.
Access Control Lists (ACLs) are the first line of defense in a... |
| V-14717 | Medium | The network element must not use SSH Version 1 for administrative access. | SSH Version 1 is a protocol that has never been defined in a standard. Since SSH-1 has inherent design flaws which make it vulnerable to, e.g., man-in-the-middle attacks, it is now generally... |
| V-30577 | Medium | The administrator must ensure that Protocol Independent Multicast (PIM) is disabled on all interfaces that are not required to support multicast routing. | A scope zone is an instance of a connected region of a given scope. Zones of the same scope cannot overlap while zones of a smaller scope will fit completely within a zone of a larger scope. For... |
| V-17815 | Medium | IGP instances configured on the OOBM gateway router do not peer only with their appropriate routing domain. | If the gateway router is not a dedicated device for the OOBM network, several safeguards must be implemented for containment of management and production traffic boundaries. Since the managed... |
| V-30646 | Medium | The administrator must ensure the perimeter router is configured to drop all inbound and outbound IPv6 packets containing an extension header with the Endpoint Identification option. | The optional and extensible natures of the IPv6 extension headers require higher scrutiny since many implementations do not always drop packets with headers that it can’t recognize and hence could... |
| V-17817 | Medium | Traffic from the managed network is able to access the OOBM gateway router | If the gateway router is not a dedicated device for the OOBM network, several safeguards must be implemented for containment of management and production traffic boundaries. It is imperative that... |
| V-17816 | Medium | The routes from the two IGP domains are redistributed to each other. | If the gateway router is not a dedicated device for the OOBM network, several safeguards must be implemented for containment of management and production traffic boundaries. Since the managed... |
| V-17819 | Medium | Management network traffic must not leak onto the managed network. | If the gateway router is not a dedicated device for the OOBM network, several safeguards must be implemented for containment of management and production traffic boundaries. To provide separation,... |
| V-17818 | Medium | Traffic from the managed network will leak into the management network via the gateway router interface connected to the OOBM backbone. | If the gateway router is not a dedicated device for the OOBM network, several safeguards must be implemented for containment of management and production traffic boundaries such as using interface... |
| V-30648 | Medium | The administrator must ensure the perimeter router is configured to drop all inbound and outbound IPv6 packets containing the NSAP address option. | The optional and extensible natures of the IPv6 extension headers require higher scrutiny since many implementations do not always drop packets with headers that it can’t recognize and hence could... |
| V-30579 | Medium | The administrator must ensure that boundaries are established at the enclave perimeter for all administrative scoped multicast traffic. | A scope zone is an instance of a connected region of a given scope. Zones of the same scope cannot overlap while zones of a smaller scope will fit completely within a zone of a larger scope. For... |
| V-30578 | Medium | The administrator must ensure that a PIM neighbor filter is bound to all interfaces that have PIM enabled. | Protocol Independent Multicast (PIM) is a routing protocol used to build multicast distribution tress for forwarding multicast traffic across the network infrastructure. PIM traffic must be... |
| V-3082 | Medium | IP Proxy ARP must be disabled on all external interfaces. | When proxy ARP is enabled on a Cisco router, it allows that router to extend the network (at Layer 2) across multiple interfaces (LAN segments). Because proxy ARP allows hosts from different LAN... |
| V-14688 | Medium | The administrator must bind the egress ACL filtering packets leaving the network to the internal interface on an inbound direction. | Access lists are used to separate data traffic into that which it will route (permitted packets) and that which it will not route (denied packets). Secure configuration of routers makes use of... |
| V-3057 | Medium | Authorized accounts must be assigned the least privilege level necessary to perform assigned duties. | By not restricting authorized accounts to their proper privilege level, access to restricted functions may be allowed before authorized personell are trained or experienced enough to use those... |
| V-18633 | Medium | The network device must drop all inbound and outbound IPv4 and IPv6 packets being tunneled with outdated protocols. | There are a number of outdated tunneling schemes that should be blocked to avoid importing IPv6 packets. DoD IPv6 IA Guidance for MO3 (S0-C7-2) has identified the following to be blocked at the... |
| V-15293 | Medium | The IAO/NSO will ensure the ingress filter drops unexpected protocol 41 packets at the 6to4 site router before sensor inspection. | 6to4 is an automated tunneling mechanism that provides v6 capability to a dual-stack node or v6 capable site that has only IPv4 connectivity to the site. One key difference between automatic 6to4... |
| V-18636 | Medium | Tunnel endpoints must be explicitly defined as auto configuration tunnels are not permitted. | IPv6-in-IPv4 tunnels require explicit configuration (on the tunnel exit point node) of both the tunnel exit point IP address and the corresponding tunnel entry point address . These are the outer... |
| V-3058 | Medium | Unauthorized accounts must not be configured for access to the network device. | A malicious user attempting to gain access to the network device may compromise an account that may be unauthorized for use. The unauthorized account may be a temporary or inactive account that... |
| V-15295 | Medium | The IAO/NSO will ensure in NAT-PT architecture there is no tunneled IPv4 in IPv6 traffic. | Network Address Translation with Protocol Translation (NAT-PT), defined in [RFC2766], is a service that can be used to translate data sent between IP-heterogeneous nodes. NAT-PT translates a IPv4... |
| V-14703 | Medium | The network device must block IPv6 Unique Local Unicast Addresses on the enclaves perimeter ingress and egress filter. | The IANA has assigned the FC00::/7 prefix to Unique Local Unicast addresses. Unique Local Address (ULA) is a routable address that is not intended to be on the Internet. Site border routers and... |
| V-14705 | Medium | The administrator will enable CEF to improve router stability during a SYN flood attack in an IPv6 enclave. | The Cisco Express Forwarding (CEF) switching mode replaces the traditional Cisco routing cache with a data structure that mirrors the entire system routing table. Because there is no need to build... |
| V-30657 | Medium | The administrator must ensure the perimeter router is configured to drop all inbound and outbound IPv6 packets containing a Hop-by-Hop or Destination Option extension header with an undefined option type.
| The optional and extensible natures of the IPv6 extension headers require higher scrutiny since many implementations do not always drop packets with headers that it can’t recognize and hence could... |
| V-15296 | Medium | The IAO/NSO will ensure interfaces supporting IPv4 in NAT-PT Architecture do not receive IPv6 traffic. | Network Address Translation with Protocol Translation (NAT-PT), defined in [RFC2766], is a service that can be used to translate data sent between IP-heterogeneous nodes. NAT-PT translates a IPv4... |
| V-14683 | Medium | The system administrator will ensure the undetermined transport packet is blocked at the perimeter in an IPv6 enclave by the router. | One of the fragmentation weaknesses known in IPv6 is the undetermined transport packet. This is a packet that contains an undetermined protocol due to fragmentation. Depending on the length of... |
| V-3982 | Medium | L2TP must not pass into the private network of an enclave. | Unlike GRE (a simple encapsulating header) L2TP is a full-fledged communications protocol with control channel, data channels, and a robust command structure. In addition to PPP, other link layer... |
| V-18608 | Medium | The IAO/NSO will ensure IPv6 6-to-4 addresses with a prefix of 2002::/16 are dropped at the enclave perimeter by the ingress and egress filters. | “6-to-4” is a tunneling IPv6 transition mechanism [RFC 3056]. The guidance is the default case, which assumes that 6-to-4 is not being used as an IPv6 transition mechanism. If 6-to-4 is... |
| V-18635 | Medium | Tunnel entry point and the tunnel exit point must contain filters for expected tunnel protocol traffic with source and destination addresses and deny the remaining traffic by default. | Tunnel endpoints that do not have the same controls as the network perimeter requirements become an unprotect entry point into the enclave. |
| V-3026 | Medium | Internet Control Message Types (ICMP) must be blocked inbound from external untrusted networks (e.g., ISP and other non-DoD networks). | Using ICMP messages for information gathering is a process allowing malicious computer attackers to launch attacks against a targeted network. In this stage the malicious attacker will try to... |
| V-3027 | Medium | Internet Control Message Types (ICMP) must be blocked outbound to external untrusted networks (e.g., ISP and other non-DoD networks). | Using ICMP messages for information gathering is a process allowing malicious computer attackers to launch attacks against a targeted network. In this stage the malicious attacker will try to... |
| V-18522 | Medium | Server VLAN interfaces must be protected by restrictive ACLs using a deny-by-default security posture. | Protecting data sitting in a server VLAN is necessary and can be accomplished using access control lists on VLANs provisioned for servers. Without proper access control of traffic entering or... |
| V-3014 | Medium | The network element must timeout management connections for administrative access after 10 minutes or less of inactivity. | Setting the timeout of the session to 10 minutes or less increases the level of protection afforded critical network components. |
| V-5618 | Medium | Gratuitous ARP must be disabled. | A gratuitous ARP is an ARP broadcast in which the source and destination MAC addresses are the same. It is used to inform the network about a host IP address. A spoofed gratuitous ARP message can... |
| V-3084 | Medium | The administrator must ensure ICMP unreachable notifications, mask replies, and redirects are disabled on all external interfaces of the premise router. | The Internet Control Message Protocol (ICMP) supports IP traffic by relaying information about paths, routes, and network conditions. Routers automatically send ICMP messages under a wide variety... |
| V-3085 | Medium | The network element must have HTTP service for administrative access disabled. | The additional services that the router is enabled for increases the risk for an attack since the router will listen for these services. In addition, these services provide an unsecured method for... |
| V-14637 | Medium | Router advertisements must be suppressed on all external-facing IPv6-enabled interfaces. | Many of the known attacks in stateless autoconfiguration are defined in RFC 3756 were present in IPv4 ARP attacks. IPSec AH was originally suggested as mitigation for the link local attacks, but... |
| V-3080 | Medium | The Configuration auto-loading feature must be disabled. | Devices can find their startup configuration either in their own NVRAM or access it over the network via TFTP or Remote Copy (rcp). Loading the image from the network is taking a security risk... |
| V-3081 | Medium | The router must have IP source routing disabled. | Source routing is a feature of IP, whereby individual packets can specify routes. This feature is used in several different network attacks by bypassing perimeter and internal defense mechanisms. |
| V-14632 | Medium | The IAO/NSO will ensure the route to the AG network adheres to the PPS CAL boundary 13 and 14 policies and is in compliance with all perimeter filtering defined in the perimeter and router sections of the Network STIG. | The enclave perimeter requirement for filtering, to include JTF-GNO PPS filtering rules, and monitoring traffic will be enforced for any traffic from the AG. All traffic entering the enclave from... |
| V-30594 | Medium | The administrator must ensure the perimeter router is configured to drop all inbound and outbound IPv6 packets containing a Hop-by-Hop header with invalid option type values. | These options are intended to be for the Destination Options header only. The optional and extensible natures of the IPv6 extension headers require higher scrutiny since many implementations do... |
| V-30660 | Medium | The administrator must ensure the 6-to-4 router is configured to drop any IPv4 packets with protocol 41 received from the internal network. | The 6to4 specific filters accomplish the role of endpoint verification and provide assurance that the tunnels are being used properly. This primary guidance assumes that only the designated 6to4... |
| V-18610 | Medium | The IAO/NSO will ensure IPv6 6bone address space is blocked on the ingress and egress filter, (3FFE::/16). | The decommissioned 6bone allocation (3FFE::/16), RFC 3701 must be blocked. It is no longer a trusted source.
|
| V-3035 | Medium | The administrator will restrict BGP connections to known IP addresses of neighbor routers from trusted Autonomous Systems. | Advertisement of routes by an autonomous system for networks that do not belong to any of its trusted peers pulls traffic away from the authorized network. This causes DoS on the network that... |
| V-3034 | Medium | The network element must authenticate all IGP peers. | A rogue router could send a fictitious routing update to convince a site’s premise router to send traffic to an incorrect or even a rogue destination. This diverted traffic could be analyzed to... |
| V-18648 | Medium | Tunnel entry and exit points must be in a deny-by-default security posture. | Having tunnels in a permit any any posture allow traffic to enter and exit the enclave without control from the Information Assurance team or SA. |
| V-14666 | Medium | Each eBGP neighbor must be authenticated with a unique password. | If the same passwords are used between eBGP neighbors, the chance of a hacker compromising any of the BGP sessions increases. It is possible that a malicious user exists in one autonomous system... |
| V-14707 | Medium | The network element must be configured from accepting any outbound IP packet that contains an illegitimate address in the source address field via egress ACL or by enabling Unicast Reverse Path Forwarding in an IPv6 enclave. | Unicast Reverse Path Forwarding (uRPF) provides a mechanism for IP address spoof protection. When uRPF is enabled on an interface, the router examines all packets received as input on that... |
| V-17754 | Medium | IPSec tunnels used to transit management traffic must be restricted to only the authorized management packets based on destination and source IP address. | The Out-of-Band Management (OOBM) network is an IP network used exclusively for the transport of OAM&P data from the network being managed to the OSS components located at the NOC. Its design... |
| V-3008 | Medium | The IAO will ensure IPSec VPNs are established as tunnel type VPNs when transporting management traffic across an ip backbone network. | Using dedicated paths, the OOBM backbone connects the OOBM gateway routers located at the premise of the managed networks and at the NOC. Dedicated links can be deployed using provisioned... |
| V-3079 | Low | The network element must have the Finger service disabled. | The finger service supports the UNIX finger protocol, which is used for querying a host about the users that are logged on. This service is not necessary for generic users. If an attacker were to... |
| V-3078 | Low | Network devices must have TCP and UDP small servers disabled. | Cisco IOS provides the "small services" that include echo, chargen, and discard. These services, especially their User Datagram Protocol (UDP) versions, are infrequently used for legitimate... |
| V-3077 | Low | Cisco Discovery Protocol (CDP) must be disabled on all external facing interfaces. | CDP is primarily used to obtain protocol addresses of neighboring devices and discover platform capabilities of those devices. Use of SNMP with the CDP Management Information Base (MIB) allows... |
| V-14667 | Low | Network devices must be configured with rotating keys used for authenticating IGP peers that have a duration exceeding 180 days. | If the keys used for routing protocol authentication are guessed, the malicious user could create havoc within the network by advertising incorrect routes and redirecting traffic. Changing the... |
| V-3070 | Low | The network element must log all attempts to establish a management connection for administrative access. | Audit logs are necessary to provide a trail of evidence in case the network is compromised. Without an audit trail that provides a when, where, who and how set of information, repeat offenders... |
| V-3072 | Low | The running configuration must be synchronized with the startup configuration after changes have been made and implemented. | If the running and startup router configurations are not synchronized properly and a router malfunctions, it will not restart with all of the recent changes incorporated. If the recent changes... |
| V-30617 | Low | The administrator must ensure that the maximum hop limit is at least 32. | The Neighbor Discovery protocol allows a hop limit value to be advertised by routers in a Router Advertisement message to be used by hosts instead of the standardized default value. If a very... |
| V-4584 | Low | The network element must log all messages except debugging and send all log data to a syslog server. | Logging is a critical part of router security. Maintaining an audit trail of system activity logs (syslog) can help identify configuration errors, understand past intrusions, troubleshoot service... |
| V-14672 | Low | The router must use its loopback or OOB management interface address as the source address when originating TACACS+ or RADIUS traffic. | Using a loopback address as the source address offers a multitude of uses for security, access, management, and scalability of routers. It is easier to construct appropriate ingress filters for... |
| V-14674 | Low | The router must use its loopback or OOB management interface address as the source address when originating NTP traffic. | Using a loopback address as the source address offers a multitude of uses for security, access, management, and scalability of routers. It is easier to construct appropriate ingress filters for... |
| V-14675 | Low | The router must use its loopback or OOB management interface address as the source address when originating SNMP traffic. | Using a loopback address as the source address offers a multitude of uses for security, access, management, and scalability of routers. It is easier to construct appropriate ingress filters for... |
| V-14676 | Low | The router must use its loopback or OOB management interface address as the source address when originating NetFlow traffic. | Using a loopback address as the source address offers a multitude of uses for security, access, management, and scalability of routers. It is easier to construct appropriate ingress filters for... |
| V-14677 | Low | The network device must use its loopback or OOB management interface address as the source address when originating TFTP or FTP traffic. | Using a loopback address as the source address offers a multitude of uses for security, access, management, and scalability of network devices. It is easier to construct appropriate ingress... |
| V-17837 | Low | The core router within the managed network has not been configured to provide preferred treatment for management traffic that must traverse several nodes to reach the management network. | When network congestion occurs, all traffic has an equal chance of being dropped.
Prioritization of network management traffic must be implemented to ensure that even during periods of severe... |
| V-17836 | Low | Management traffic is not classified and marked at the nearest upstream MLS or router when management traffic must traverse several nodes to reach the management network. | When network congestion occurs, all traffic has an equal chance of being dropped.
Prioritization of network management traffic must be implemented to ensure that even during periods of severe... |
| V-23747 | Low | The network element must use two or more NTP servers to synchronize time. | Without synchronized time, accurately correlating information between devices becomes difficult, if not impossible. If you cannot successfully compare logs between each of your routers, switches,... |
| V-5615 | Low | Network devices must have TCP Keep-Alives enabled for TCP sessions. | Idle TCP sessions can be susceptible to unauthorized access and hijacking attacks. By default, routers do not continually test whether a previously connected TCP endpoint is still reachable. If... |
| V-4624 | Low | The IAO/NSO will ensure the AG network service provider IP addresses are not redistributed into or advertised to the NIPRNet or any router belonging to any other Autonomous System (AS) i.e. to another AG device in another AS. | Unsolicited traffic that may inadvertently attempt to enter the NIPRNet by traversing the enclave's premise router can be avoided by not redistributing NIPRNet routes into the AG. |
| V-19189 | Low | The administrator must ensure that multicast routers are configured to establish
boundaries for Admin-local or Site-local scope multicast traffic. | A scope zone is an instance of a connected region of a given scope. Zones of the same scope cannot overlap while zones of a smaller scope will fit completely within a zone of a larger scope. For... |
| V-17823 | Low | The management interface must be configured as passive for the IGP instance deployed in the managed network. | The OOBM access switch will connect to the management interface of the managed network devices. The management interface can be a true OOBM interface or a standard interface functioning as the... |
| V-30736 | Low | The administrator must ensure the 6-to-4 router is configured to drop any outbound IPv6 packets from the internal network with a source address that is not within the 6to4 prefix 2002:V4ADDR::/48 where V4ADDR is the designated IPv4 6to4 address for the enclave. | An automatic 6to4 tunnel allows isolated IPv6 domains to be connected over an IPv4 network and allows connections to remote IPv6 networks. The key difference between this deployment and manually... |
| V-14673 | Low | The router must use its loopback or OOB management interface address as the source address when originating syslog traffic. | Using a loopback address as the source address offers a multitude of uses for security, access, management, and scalability of routers. It is easier to construct appropriate ingress filters for... |
| V-14681 | Low | The router must use its loopback interface address as the source address for all iBGP peering sessions. | Using a loopback address as the source address offers a multitude of uses for security, access, management, and scalability. It is easier to construct appropriate filters for control plane... |
| V-5617 | Low | DHCP Services must be disabled. | By sending a large packet to the Dynamic Host Configuration Protocol (DHCP) port it is possible to freeze the routers processing engine. |
| V-5616 | Low | Network devices must have identification support disabled. | Identification support allows one to query a TCP port for identification. This feature enables an unsecured protocol to report the identity of a client initiating a TCP connection and a host... |
| V-3020 | Low | The network element must have DNS servers defined if it is configured as a client resolver. | The susceptibility of IP addresses to spoofing translates to DNS host name and IP address mapping vulnerabilities. For example, suppose a source host wishes to establish a connection with a... |
| V-5614 | Low | Network devices must have the PAD service disabled. | Packet Assembler Disassembler (PAD) is an X.25 component seldom used. It collects the data transmissions from the terminals and gathers them into a X.25 data stream and vice versa. PAD acts like... |
| V-3028 | Low | Trace routes originating from untrusted networks (e.g., ISP and other non-DoD networks) must be blocked to prevent network discovery by unauthorized users. | The trace route tool will display routes and trip times on an IP network. An attacker can use trace route responses to create a map of the subnets and hosts behind the perimeter router, just as... |
| V-3086 | Low | BOOTP services must be disabled. | BOOTP is a user datagram protocol (UDP) that can be used by Cisco routers to access copies of Cisco IOS Software on another Cisco router running the BOOTP service. In this scenario, one Cisco... |
| V-3083 | Low | IP directed broadcast must be disabled on all layer 3 interfaces. | An IP directed broadcast is a datagram sent to the broadcast address of a subnet that is not directly attached to the sending machine. The directed broadcast is routed through the network as a... |
| V-30585 | Low | The administrator must ensure that multicast groups used for source specific multicast (SSM) routing are from the specific multicast address space reserved for this purpose. | Packet origin is a concern because unauthorized sources could potentially send multicast data to a group, using any source address that is permitted. The unauthorized data could impact the... |
| V-7011 | Low | The network element’s auxiliary port must be disabled unless it is connected to a secured modem providing encryption and authentication. | The use of POTS lines to modems connecting to network devices provides clear text of authentication traffic over commercial circuits that could be captured and used to compromise the network. ... |
| V-3000 | Low | The network device must log all access control lists (ACL) deny statements. | Auditing and logging are key components of any security architecture. It is essential for security personnel to know what is being done, attempted to be done, and by whom in order to compile an... |
