The Juniper perimeter router must be configured to deny network traffic by default and allow network traffic by exception.

Overview

Finding ID	Version	Rule ID	IA Controls	Severity
V-217029	JUNI-RT-000240	SV-217029r639663_rule		High

Description
A deny-all, permit-by-exception network communications traffic policy ensures that only connections that are essential and approved are allowed. This requirement applies to both inbound and outbound network communications traffic. All inbound and outbound traffic must be denied by default. Firewalls and perimeter routers should only allow traffic through that is explicitly permitted. The initial defense for the internal network is to block any traffic at the perimeter that is attempting to make a connection to a host residing on the internal network. In addition, allowing unknown or undesirable outbound traffic by the firewall or router will establish a state that will permit the return of this undesirable traffic inbound.

Description

A deny-all, permit-by-exception network communications traffic policy ensures that only connections that are essential and approved are allowed. This requirement applies to both inbound and outbound network communications traffic. All inbound and outbound traffic must be denied by default. Firewalls and perimeter routers should only allow traffic through that is explicitly permitted. The initial defense for the internal network is to block any traffic at the perimeter that is attempting to make a connection to a host residing on the internal network. In addition, allowing unknown or undesirable outbound traffic by the firewall or router will establish a state that will permit the return of this undesirable traffic inbound.

STIG	Date
Juniper Router RTR Security Technical Implementation Guide	2021-02-11

Details

Check Text ( C-18258r296955_chk )
This requirement is not applicable for the DoDIN Backbone. Review the router configuration to verify that the inbound filter applied to all external interfaces is configured to allow specific ports and protocols and deny all other traffic. Verify that an inbound filter is applied to all external interfaces as shown in the example below. interfaces { ge-0/0/0 { unit 0 { family inet { filter { input FILTER_INBOUND_TRAFFIC; } address 11.1.12.2/24; } } } Review inbound filters to verify that the ending term is configured to deny all other traffic that is not explicitly allowed. firewall { family inet { filter FILTER_INBOUND_TRAFFIC { term ALLOW_BGP { from { destination-address { 11.1.24.0/24; } protocol tcp; destination-port bgp; } then accept; } … … … term ALLOW_XYZ { from { protocol xyz; } then accept; } term DENY_ALL_OTHER { then { syslog; discard; } } } If the filter is not configured to allow specific ports and protocols and deny all other traffic, this is a finding. If the filter is not configured inbound on all external interfaces, this is a finding.

Check Text ( C-18258r296955_chk )

This requirement is not applicable for the DoDIN Backbone.

Review the router configuration to verify that the inbound filter applied to all external interfaces is configured to allow specific ports and protocols and deny all other traffic.

Verify that an inbound filter is applied to all external interfaces as shown in the example below.

interfaces {
ge-0/0/0 {
unit 0 {
family inet {
filter {
input FILTER_INBOUND_TRAFFIC;
}
address 11.1.12.2/24;
}
}
}

Review inbound filters to verify that the ending term is configured to deny all other traffic that is not explicitly allowed.

firewall {
family inet {
filter FILTER_INBOUND_TRAFFIC {
term ALLOW_BGP {
from {
destination-address {
11.1.24.0/24;
}
protocol tcp;
destination-port bgp;
}
then accept;
}
…
…
…
term ALLOW_XYZ {
from {
protocol xyz;
}
then accept;
}
term DENY_ALL_OTHER {
then {
syslog;
discard;
}
}
}

If the filter is not configured to allow specific ports and protocols and deny all other traffic, this is a finding.

If the filter is not configured inbound on all external interfaces, this is a finding.

Fix Text (F-18256r296956_fix)
This requirement is not applicable for the DoDIN Backbone. Configure a term at the end of the inbound filter to deny all other traffic by default as shown in the example below. [edit firewall family inet] set filter FILTER_INBOUND_TRAFFIC term DENY_ALL_OTHER then syslog discard