If STP is used, the Juniper EX switch must be configured to implement Rapid STP, or Multiple STP, where VLANs span multiple switches with redundant links.
Overview
| Finding ID | Version | Rule ID | IA Controls | Severity |
|---|---|---|---|---|
| V-253964 | JUEX-L2-000170 | SV-253964r843925_rule | Medium |
| Description |
|---|
| Spanning Tree Protocol (STP) is implemented on bridges and switches to prevent layer 2 loops when a broadcast domain spans multiple bridges and switches and when redundant links are provisioned to provide high availability in case of link failures. Convergence time can be significantly reduced using Rapid STP (802.1w) instead of STP (802.1d), resulting in improved availability. Rapid STP should be deployed by implementing either Rapid Spanning-Tree Protocol (RSTP) or Multiple Spanning-Tree Protocol (MSTP), the latter scales much better when there are many VLANs. In cases where VLANs do not span multiple switches, it is a best practice to not implement STP. Avoiding the use of STP will provide the most deterministic and highly available network topology. If STP is required, then review the switch configuration to verify that Rapid STP or Multiple STP has been implemented. RSTP and MSTP are similar, except MSTP is more granular, flexible, and scalable. RTSP and MSTP can be enabled simultaneously, but in general only one STP is configured. |
| STIG | Date |
|---|---|
| Juniper EX Series Switches Layer 2 Switch Security Technical Implementation Guide | 2022-08-31 |
Details
| Check Text ( C-57416r843923_chk ) |
|---|
| If STP is required, then review the switch configuration to verify that Rapid STP or Multiple STP has been implemented. RSTP and MSTP are similar, except MSTP is more granular, flexible, and scalable. RTSP and MSTP can be enabled simultaneously, but in general only one STP is configured. RSTP: [edit protocols rstp] rstp { bridge-priority (0..61440 in 4k increments); << e.g. 0, 4k, 8k...60k interface edge; } interface mode point-to-point; } bpdu-block-on-edge; } -OR- MSTP: [edit protocols mstp] configuration-name revision-level (0..65535); max-age (6..40 seconds); hello-time (1..10 seconds); forward-delay (4..30 seconds); bridge-priority (0..61440 in 4k increments); << e.g. 0, 4k, 8k...60k bpdu-block-on-edge; interface edge; } interface mode point-to-point; } msti 3 { bridge-priority (0..61440 in 4k increments); << e.g. 0, 4k, 8k...60k vlan [ vlan-id-1 vlan-id-2 ]; } If Rapid STP or Multiple STP has not been implemented where an STP is required, this is a finding. |
| Fix Text (F-57367r843924_fix) |
|---|
| Configure Rapid STP to be implemented at the access and distribution layers where VLANs span multiple switches. RSTP: set protocols rstp bridge-priority (0..61440 in 4k increments) << e.g. 0, 4k, 8k...60k set protocols rstp interface set protocols rstp interface set protocols rstp bpdu-block-on-edge MSTP: set protocols mstp configuration-name set protocols mstp revision-level (0..65535) set protocols mstp max-age (6..40 seconds) set protocols mstp hello-time (1..10 seconds) set protocols mstp forward-delay (4..30 seconds) set protocols mstp bridge-priority (0..61440 in 4k increments) << e.g. 0, 4k, 8k...60k set protocols mstp bpdu-block-on-edge set protocols mstp interface set protocols mstp interface set protocols mstp msti 3 bridge-priority (0..61440 in 4k increments) << e.g. 0, 4k, 8k...60k set protocols mstp msti 3 vlan set protocols mstp msti 3 vlan |