The Cisco PE router must be configured to enforce the split-horizon rule for all pseudowires within a Virtual Private LAN Services (VPLS) bridge domain.

Overview

Finding ID	Version	Rule ID	IA Controls	Severity
V-96801	CISC-RT-000690	SV-105939r1_rule		Low

Description
A virtual forwarding instance (VFI) must be created on each participating PE router for each customer VLAN using VPLS for carrier Ethernet services. The VFI specifies the VPN ID of a VPLS domain, the addresses of other PE routers in the domain, and the type of tunnel signaling and encapsulation mechanism for each peer PE router. The set of VFIs formed by the interconnection of the emulated VCs is called a VPLS instance, which forms the logic bridge over the MPLS core network. The PE routers use the VFI with a unique VPN ID to establish a full mesh of emulated virtual circuits or pseudowires to all the other PE routers in the VPLS instance. The full-mesh configuration allows the PE router to maintain a single broadcast domain. With a full-mesh configuration, signaling and packet replication requirements for each provisioned virtual circuit on a PE can be high. To avoid the problem of a packet looping in the provider core, thereby adding more overhead, the PE devices must enforce a split-horizon principle for the emulated virtual circuits; that is, if a packet is received on an emulated virtual circuit, it is not forwarded on any other virtual circuit.

Description

A virtual forwarding instance (VFI) must be created on each participating PE router for each customer VLAN using VPLS for carrier Ethernet services. The VFI specifies the VPN ID of a VPLS domain, the addresses of other PE routers in the domain, and the type of tunnel signaling and encapsulation mechanism for each peer PE router. The set of VFIs formed by the interconnection of the emulated VCs is called a VPLS instance, which forms the logic bridge over the MPLS core network. The PE routers use the VFI with a unique VPN ID to establish a full mesh of emulated virtual circuits or pseudowires to all the other PE routers in the VPLS instance. The full-mesh configuration allows the PE router to maintain a single broadcast domain. With a full-mesh configuration, signaling and packet replication requirements for each provisioned virtual circuit on a PE can be high. To avoid the problem of a packet looping in the provider core, thereby adding more overhead, the PE devices must enforce a split-horizon principle for the emulated virtual circuits; that is, if a packet is received on an emulated virtual circuit, it is not forwarded on any other virtual circuit.

STIG	Date
Cisco IOS XR Router RTR Security Technical Implementation Guide	2019-07-24

Details

Check Text ( C-95637r1_chk )
Review the PE router configuration to verify that split horizon is enabled at each attachment circuit within each bridge domain as shown in the example below. bridge group L2GROUP bridge-domain L2_BRIDGE_COI1 interface GigabitEthernet0/0/0/2 split-horizon group ! If split horizon is not enabled, this is a finding. Note: This requirement is only applicable to a mesh VPLS topology. VPLS solves the loop problem by using a split-horizon rule which states that member PE routers of a VPLS must forward VPLS traffic only to the local attachment circuits when they receive the traffic from the other PE routers. In a ring VPLS, split horizon must be disabled so that a PE router can forward a packet received from one pseudowire to another pseudowire. To prevent the consequential loop, at least one span in the ring would not have a pseudowire for any given VPLS instance.

Check Text ( C-95637r1_chk )

Review the PE router configuration to verify that split horizon is enabled at each attachment circuit within each bridge domain as shown in the example below.

bridge group L2GROUP
bridge-domain L2_BRIDGE_COI1
interface GigabitEthernet0/0/0/2
split-horizon group
!

If split horizon is not enabled, this is a finding.

Note: This requirement is only applicable to a mesh VPLS topology. VPLS solves the loop problem by using a split-horizon rule which states that member PE routers of a VPLS must forward VPLS traffic only to the local attachment circuits when they receive the traffic from the other PE routers. In a ring VPLS, split horizon must be disabled so that a PE router can forward a packet received from one pseudowire to another pseudowire. To prevent the consequential loop, at least one span in the ring would not have a pseudowire for any given VPLS instance.

Fix Text (F-102481r1_fix)
Enable split horizon on all PE routers deploying VPLS in a full-mesh configuration. RP/0/0/CPU0:R3(config)#l2vpn RP/0/0/CPU0:R3(config-l2vpn)#bridge group L2GROUP RP/0/0/CPU0:R3(config-l2vpn-bg)#bridge-domain L2_BRIDGE_COI1 RP/0/0/CPU0:R3(config-l2vpn-bg-bd)#interface GigabitEthernet0/0/0/2 RP/0/0/CPU0:R3(config-l2vpn-bg-bd-ac)#split-horizon group RP/0/0/CPU0:R3(config-l2vpn-bg-bd-ac)#end