The Cisco multicast Designated switch (DR) must be configured to filter the Internet Group Management Protocol (IGMP) and Multicast Listener Discovery (MLD) Report messages to allow hosts to join only multicast groups that have been approved by the organization.

Overview

Finding ID	Version	Rule ID	IA Controls	Severity
V-220464	CISC-RT-000860	SV-220464r864160_rule		Low

Description
Real-time multicast traffic can entail multiple large flows of data. Large unicast flows tend to be fairly isolated (i.e., someone doing a file download here or there), whereas multicast can have broader impact on bandwidth consumption, resulting in extreme network congestion. Hence, it is imperative that there is multicast admission control to restrict which multicast group's hosts are allowed to join via IGMP or MLD.

Description

Real-time multicast traffic can entail multiple large flows of data. Large unicast flows tend to be fairly isolated (i.e., someone doing a file download here or there), whereas multicast can have broader impact on bandwidth consumption, resulting in extreme network congestion. Hence, it is imperative that there is multicast admission control to restrict which multicast group's hosts are allowed to join via IGMP or MLD.

STIG	Date
Cisco IOS Switch RTR Security Technical Implementation Guide	2022-09-14

Details

Check Text ( C-22179r508467_chk )
Review the configuration of the DR to verify that it is filtering IGMP or MLD Membership Report messages, allowing hosts to join only groups that have been approved. Step 1: Verify that all host-facing Layer 3 and VLAN interfaces are configured to filter IGMP Membership Report messages (IGMP joins) as shown in the example below: interface Vlan3 ip address 10.3.3.3 255.255.255.0 ip pim sparse-mode ip igmp access-group IGMP_JOIN_FILTER ip igmp version 3 Step 2: Verify that the ACL denies unauthorized groups or permits only authorized groups. The example below denies all groups from 239.8.0.0/16 range. ip access-list standard IGMP_JOIN_FILTER deny 239.8.0.0 0.0.255.255 permit any Note: This requirement is only applicable to Source Specific Multicast (SSM) implementation. This requirement is not applicable to Any Source Multicast (ASM) since the filtering is being performed by the Rendezvous Point switch. If the DR is not filtering IGMP or MLD Membership Report messages, this is a finding.

Check Text ( C-22179r508467_chk )

Review the configuration of the DR to verify that it is filtering IGMP or MLD Membership Report messages, allowing hosts to join only groups that have been approved.

Step 1: Verify that all host-facing Layer 3 and VLAN interfaces are configured to filter IGMP Membership Report messages (IGMP joins) as shown in the example below:

interface Vlan3
ip address 10.3.3.3 255.255.255.0
ip pim sparse-mode
ip igmp access-group IGMP_JOIN_FILTER
ip igmp version 3

Step 2: Verify that the ACL denies unauthorized groups or permits only authorized groups. The example below denies all groups from 239.8.0.0/16 range.

ip access-list standard IGMP_JOIN_FILTER
deny 239.8.0.0 0.0.255.255
permit any

Note: This requirement is only applicable to Source Specific Multicast (SSM) implementation. This requirement is not applicable to Any Source Multicast (ASM) since the filtering is being performed by the Rendezvous Point switch.

If the DR is not filtering IGMP or MLD Membership Report messages, this is a finding.

Fix Text (F-22168r508468_fix)
Configure the DR to filter the IGMP or MLD Membership Report messages to allow hosts to join only multicast groups that have been approved. Step 1: Configure the ACL to filter IGMP Membership Report messages as shown in the example below: SW2(config)#ip access-list standard IGMP_JOIN_FILTER SW2(config-std-nacl)#deny 239.8.0.0 0.0.255.255 SW2(config-std-nacl)#permit any SW2(config-std-nacl)#exit Step 2: Apply the filter to all host-facing Layer 3 and VLAN interfaces. SW2(config)#int vlan3 SW2(config-if)#ip igmp access-group IGMP_JOIN_FILTER

Fix Text (F-22168r508468_fix)

Configure the DR to filter the IGMP or MLD Membership Report messages to allow hosts to join only multicast groups that have been approved.

Step 1: Configure the ACL to filter IGMP Membership Report messages as shown in the example below:

SW2(config)#ip access-list standard IGMP_JOIN_FILTER
SW2(config-std-nacl)#deny 239.8.0.0 0.0.255.255
SW2(config-std-nacl)#permit any
SW2(config-std-nacl)#exit

Step 2: Apply the filter to all host-facing Layer 3 and VLAN interfaces.

SW2(config)#int vlan3
SW2(config-if)#ip igmp access-group IGMP_JOIN_FILTER