Changes are coming to https://stigviewer.com.
Take our survey to help us understand your usage and how we can better serve you in the future.
Take Survey
The Cisco switch must be configured to restrict traffic destined to itself.
Overview
| Finding ID | Version | Rule ID | IA Controls | Severity |
|---|---|---|---|---|
| V-220996 | CISC-RT-000130 | SV-220996r622190_rule | High |
| Description |
|---|
| The route processor handles traffic destined to the switch—the key component used to build forwarding paths and is instrumental with all network management functions. Hence, any disruption or DoS attack to the route processor can result in mission critical network outages. |
| STIG | Date |
|---|---|
| Cisco IOS-XE Switch RTR Security Technical Implementation Guide | 2022-09-13 |
Details
| Check Text ( C-22711r408782_chk ) |
|---|
| Review the external and internal ACLs to verify that the switch is configured to only allow specific management and control plane traffic from specific sources destined to itself. Step 1: Verify ACLs has been configured as shown in the example below that matches expected control plane and management plane traffic. With the exception of Internet Control Message Protocol (ICMP), all other traffic destined to the switch should be dropped. ip access-list extended EXTERNAL_ACL permit tcp host x.11.1.1 eq bgp host x.11.1.2 permit tcp host x.11.1.1 host x.11.1.2 eq bgp permit icmp host x.11.1.1 host x.11.1.2 echo permit icmp host x.11.1.1 host x.11.1.2 echo-reply deny ip any host x.11.1.1 log-input permit … … … … deny ip any any log-input ip access-list extended INTERNAL_ACL permit icmp any any permit ospf host 10.1.12.1 host 10.1.12.2 permit tcp 10.2.1.0 0.0.0.255 host 10.1.12.2 eq 22 permit tcp 10.2.1.0 0.0.0.255 host 10.1.12.2 eq tacacs permit udp 10.2.1.0 0.0.0.255 host 10.1.12.2 eq snmp permit udp 10.2.1.0 0.0.0.255 host 10.1.12.2 eq ntp deny ip any host 10.1.12.2 log-input permit … … … … deny ip any any log-input Note: For the internal ACL example, all switches within the hypothetical network (10.1.0.0/16) have been configured to use the loopback address to source all management traffic (not shown); hence, the loopbacks are the only allowable destination address for management traffic. In addition, all management traffic destined to the switch must originate from the management network (10.2.1.0/24). With the exception of link-local control plane traffic and ICMP, all other traffic destined to any physical interface address will be dropped. Step 2: Verify that the ACL has been applied to the appropriate interface as shown in the example below: interface GigabitEthernet0/2 no switchport ip address x.11.1.2 255.255.255.254 ip access-group EXTERNAL_ACL in interface GigabitEthernet0/3 no switchport ip address 10.1.12.2 255.255.255.0 ip access-group INTERNAL_ACL in If the switch is not configured to restrict traffic destined to itself, this is a finding. |
| Fix Text (F-22700r408783_fix) |
|---|
| Step 1: Configure the ACL for any external interfaces as shown in the example below: SW1(config)#ip access-list extended EXTERNAL_ACL SW1(config-ext-nacl)#permit tcp host x.11.1.1 eq bgp host x.11.1.2 SW1(config-ext-nacl)#permit tcp host x.11.1.1 host x.11.1.2 eq bgp SW1(config-ext-nacl)#permit icmp host x.11.1.1 host x.11.1.2 echo SW1(config-ext-nacl)#permit icmp host x.11.1.1 host x.11.1.2 echo-reply SW1(config-ext-nacl)#deny ip any host x.11.1.1 log-input SW1(config-ext-nacl)#permit … … … … SW1(config-ext-nacl)#deny ip any any log-input Step 2: Configure the ACL for any external interfaces as shown in the example below: SW1(config)#ip access-list extended INTERNAL_ACL SW1(config-ext-nacl)#permit ospf host 10.1.12.1 host 10.1.12.2 SW1(config-ext-nacl)#permit tcp 10.2.1.0 0.0.0.255 host 10.1.12.2 eq 22 SW1(config-ext-nacl)#permit tcp 10.2.1.0 0.0.0.255 host 10.1.12.2 eq tacacs SW1(config-ext-nacl)#permit udp 10.2.1.0 0.0.0.255 host 10.1.12.2 eq snmp SW1(config-ext-nacl)#permit udp 10.2.1.0 0.0.0.255 host 10.1.12.2 eq ntp SW1(config-ext-nacl)#deny ip any host 10.1.12.2 log-input SW1(config-ext-nacl)#permit … … … … SW1(config-ext-nacl)#permit ip any any log-input SW1(config-ext-nacl)#exit Note: Best practice is to configure the ACL statements relative to traffic destined to the switch first followed by ACL statements for transit traffic. Step 3: Apply the ACLs to the appropriate interface as shown in the example below: SW1(config)#int g0/2 SW1(config-if)#ip access-group EXTERNAL_ACL in SW1(config)#int g0/3 SW1(config-if)#ip access-group INTERNAL_ACL in |