The Cisco ASA must be configured to inspect all inbound and outbound IPv6 traffic for unknown or out-of-order extension headers.

Overview

Finding ID	Version	Rule ID	IA Controls	Severity
V-239870	CASA-FW-000280	SV-239870r665896_rule		Medium

Description

IPv6 packets with unknown extension headers as well as out-of-order headers can create Denial-of-Service attacks for other networking components as well as host devices. IPv6 inspection can check conformance to RFC 2460 enforcing the order extension headers. While routers only need to examine the IPv6 destination address and the Hop-by-Hop Options header, firewalls must recognize and parse through all existing extension headers since the upper-layer protocol information resides in the last header. An attacker is able to chain many extension headers in order to pass firewall and intrusion detections. An attacker can cause a denial of service if an intermediary device or destination host is not capable of processing an extensive or out-of-order chain of extension headers. Hence, it is imperative the firewall is configured to drop packets with unknown or out-of-order headers.

STIG	Date
Cisco ASA Firewall Security Technical Implementation Guide	2021-03-15

Details

Check Text ( C-43103r665894_chk )

Review the firewall configuration to verify that IPv6 inspection is being performed on all interfaces. Step 1: Verify that the inspect ipv6 command is configured under the global policy map as shown in the example below. policy-map global_policy class inspection_default … … … inspect ipv6 IPV6_MAP Step 2: If a policy map is specified for the inspect ipv6 command, verify the parameters command has been configured. Also verify that the “no verify-header order” and “no verify-header type” sub-command are not configured under the parameters command. policy-map type inspect ipv6 IPV6_MAP parameters match header hop-by-hop drop log match header routing-type eq 0 drop log match header routing-type eq 1 drop log match header routing-type range 3 255 drop log match header destination-option drop log Note: If policy map is not specified for the inspect ipv6 command, the default IPv6 inspection policy map is used and the following actions are taken: 1. Allows only known IPv6 extension headers. Non-conforming packets are dropped and logged. 2. Enforces the order of IPv6 extension headers as defined in the RFC 2460 specification. Non-conforming packets are dropped and logged. 3. Drops any packet with a routing type header. Note: This requirement is not applicable if IPv6 is not enabled on any interfaces. If the firewall is not configured to inspect all inbound and outbound IPv6 traffic for unknown or out-of-order extension headers, this is a finding.

Fix Text (F-43062r665895_fix)

Configure the firewall to inspect all inbound and outbound IPv6 traffic for unknown or out-of-order extension headers. Step 1 (optional): Configure an IPv6 inspect policy map. ASA(config)# policy-map type inspect ipv6 IPV6_MAP ASA(config-pmap)# parameters ASA(config-pmap-p)# verify-header type ASA(config-pmap-p)# verify-header order ASA(config-pmap-p)# exit ASA(config-pmap)# match header hop-by-hop ASA(config-pmap-c)# drop log ASA(config-pmap-c)# exit ASA(config-pmap)# match header routing-type eq 0 ASA(config-pmap-c)# drop log ASA(config-pmap-c)# exit ASA(config-pmap)# match header routing-type eq 1 ASA(config-pmap-c)# drop log ASA(config-pmap-c)# exit ASA(config-pmap)# match header routing-type range 3 255 ASA(config-pmap-c)# drop log ASA(config-pmap-c)# exit Note: The verify-header type and verify-header order are enabled by default when the parameters command is configured. Step 2: Include the inspect ipv6 command in the global policy-map as shown in the example below. ASA(config)# policy-map global_policy ASA(config-pmap)# class inspection_default ASA(config-pmap-c)# inspect ipv6 ASA(config-pmap-c)# end